Various Parts and Tool


3/4 open end wrench for oil plug
30w Oil Non-detergent

Spark Plugs:

 Autolite 3076
15/16 open end wrench or deep socket
Gap -0.030

 Carburetor 

 Carter RAJX-O

 2 - Bolts to intake - (1/2)
Bowl Nut - (3/4)

Vacuum Fuel Feed System:

 Stewart Model No. 215g
Bolts to hold the pump to the frame - (7/16)
website reference:  http://hudsonterraplane.com/tech/1927/StewartWarnerVacuumTank2-11-27.pdf
Fuel tank to vacuum pump - (19/32) 
Vacuum Pump end (19/32) to carburetor (11/16)
           Vacuum Line - (5/8)
Fuel Line Petcock - (7/16)
Top of Vacuum Fuel tank from gas tank - (1/2)

Generator

Delco Remy

Still working on the number but it is either :
943B or 943J
The more I talk to people they keep saying most likely a 943B.

3 Bolts that hold the generator in place are 1/2 inch.

Starter Parts

Button - Bolts on the inside of the engine compartment - (7/16)
Wires to be connect to the button (#13)

Battery Terminal - (#13)

Starter "Motor" - Delco - Remy 710-D

Ignition Coil

Ignition Coil wire to Distributor side - (3/8)
Top of Ignition Coil to hold distributor wires (8mm)
Top of Ignition Coil - nut that goes to side of distributor - (5/16)
Delco - Remy
Model - 526-B
Condenser nut - 13/32 open end wrench

Distributor

Firing order - 1,2,4,3
Point Gap - 0.025

Delco - Remy
Model - 635B
Serial - 770096
Dayton, Ohio   and   Anderson, IND
Automotive Electrical Equipment
website reference: http://my28chev.blogspot.com/2012/01/gamble-pays-off-nos-distributor.html 

Ignition Timing Reference

file:///C:/Users/Owner/Downloads/show_pdf%20(4).pdf

Steering

1 1/15th socket for Pitman Arm Shaft Nut
3/4 socket for King Bolt Nut


Mirror - Driver Side

Bracket bolts on the truck that hold arm - 7/16 inch 

Nut to tighten Mirror to Arm - 1/2 inch


Comments

Post a Comment

Popular posts from this blog

Horn Works - Klaxon - 8C 6volts

Image
Thanks to my brother-in-law Eugene and my Nephew Dave (good name) we got a lot of the electrical working on Sunday - 24 June.  I was in the house when I heard the distinct noise that brought me back to my submarine days - Dive - Dive - Dive - alright maybe not exactly the same - but still a good and distinct noise that got some neighbors out of the house to come over and inspect what was going on.    So - the horn has been working on and off - seems it works for like 3-4 blasts and then it stops.  So I took it apart and checked it out, cleaned what I could and put it all together. I didn't put it back in the truck because it is like 100 degrees outside today. Here are some of the pieces I was working on in the house with A/C. Information off the horn: Klaxon - 8C 6 volts Delco - Remy Corp. Anderson, IND. USA Holding the horn together - 6 bolts - 3/8 in. open end 2 bolts horn bracket to frame - 1/2 in.
Read more

KISS

Image
No not the Band from the 70's. I think it stands for Keep it Simple - not sure what the last S is. Thanks Bob for becoming a follower. So yesterday, 17 April, I wanted to make sure the truck was going to continue to start on a regular basis - after all it should right - It has a rebuilt generator/regulator, starter and new starter button, battery cables, fresh gas and condenser.   Yeah - not so simple - it continued to backfire and not want to start.  I know if Jeffery was here he would say - its not getting gas, is there gas in the tank Dave? Keep it Simple Dave - yes there is gas in the tank - Jeffery, (why is Jeffery in my head and I am answering him?) Guess its time to call Eugene. He suggested I check the Vacuum Fuel Feed System Filter to make sure it wasn't clogged. Good call Eugene. Thanks for helping me Keep it Simple.... Put that all back together, but still not wanting to start. So I drained the gas from the tank, disconnec
Read more

Street Legal

Image
Thursday, I took the truck down to the church - 3.1 miles one way - for a test run before I had to go for inspection on the 7th.  Worked great, still have some leaking oil, antifreeze and gas, but otherwise it ran good. On the 7th of June 2019, and after some horn issues getting worked out, I drove the truck to Monroe Auto Shop in Queensbury to get inspected.  I told the manager Mike that I would be there at 0730, but I arrived around 1030.  The shop was happy to see the truck and the inspection went well.  Thanks to my sister Kathy for following me the 7 miles - one way - I needed to go for the inspection.  There was a line of traffic behind us, but I don't think people cared.  People were waving and giving me the thumbs up - okay - I thought it was a thumbs up............. On the way home, I stopped by Randy's Barber Shop in Hudson Falls to show him the truck and got to talking with someone about the upcoming car shows.  Just need to give my baby a bath and some shin
Read more